Sometimes when installing Windows, including version 10, an error message is displayed on the screen. The text of the message is: "Windows cannot be installed to this drive." In this case, the hard drive is displayed in the BIOS. It is also visible at the stage of installing the operating system, where it could be divided into sections.
This problem occurs for two reasons:
In addition to an error message informing you that Windows 7 or 10 cannot be installed on this drive, if you have problems with AHCI mode, the computer cannot boot from the selected drive. The reason is that the controller may have been disabled in the BIOS.
The problem is solved in the following way:
Another reason for the impossibility of installing Windows 7 or 10 versions with the display of a similar message may be GPT - the hard disk partition format.
More recently, all hard drives were of the same type. The only partition style was MBR. Over the past few years, manufacturers have been gradually switching to the production of hard drives with the GPT format. But boot files with OS are not modified for new formats, and as a result, the above error appears during installation.
The MBR (Master Boot Record) is the program code and data required to prestart a computer. They are located in the initial marked sector of the hard drive. The start of the MBR begins after the initial BIOS analysis of the health of all devices. Its main function is to locate the files that are needed to boot the OS.
GPT is a new standard for the volume table layout format. A standard built-in interface has also been developed software for computers, replacing the BIOS. It is called UEFI (Unified Extensible Firmware Interface).
The problem occurs due to the fact that the OS installer cannot install Windows to the specified partition, due to the fact that the partition table does not fit it.
There are 2 methods to fix the problem:
The choice of method should be determined by the following rules:
Using the MBR limits some features such as:
Problems installing the OS on a GPT volume usually arise for those who want to install Windows 7, 8 and 10.
To install an OS on a GPT volume, 2 conditions must be met:
If the first condition is not met, it is necessary to prepare a bootable UEFI drive.
But in most cases, only the second condition is not met. Therefore, it is more advisable to immediately go into the BIOS and check the settings.
There are two options to set in the BIOS:
After saving the settings on the computer, you can install the OS. The error won't happen again.
There are several options for converting volume styles. Let's consider them in more detail.
This method is optimal for use in a situation where installing OS such as Windows 7, 8, 10 is not feasible due to the type of GPT volumes. It can also be useful not only when installing the OS, but also during the regular operation of the OS to convert non-system partitions.
It should not be forgotten that when converting partitions, all information from them will be lost. Therefore, it is recommended to save everything important in advance on an external storage medium.
To change the volume style from GPT to MBR via command line necessary:
You can create volumes on the HDD by selecting the item " Customize Disk».
The volume style change is complete.
An alternative volume conversion method requires a properly functioning Windows 7, 8 or 10 operating system on a personal computer. You can only convert a disk volume that is not a system disk.
The sequence of steps for converting an HDD volume is as follows:
Except standard methods HDD volume conversion provided by Microsoft developers, you can use third-party hard disk volume management utilities such as
During the installation of the operating Windows systems 10 may occur various errors. As a rule, they are associated with incorrect BIOS settings or incorrect operation of computer or laptop components. One of common mistakes sounds like this: Windows installation on this disc is not possible. Perhaps the equipment this computer does not support booting from this disk. Make sure the controller for this drive is enabled in the computer's BIOS menu." Yes, there are troubles when the disk is really cut off and no longer works. But most often the reason is something else.
The most common reason why this malfunction occurs is in the settings of the SATA controller when working with old hard drives. Try to start when you turn on the PC, enter the BIOS and change the controller mode from ACHI to IDE.
On more modern motherboards with UEFI instead of the regular BIOS, changing to Legacy mode may help.
If none of these manipulations help, then return everything as it was. The reason is most likely something else.
Sometimes the error “Make sure that the controller of this disk is enabled in the computer’s BIOS menu” may appear because the boot record of the hard disk has crooked and needs to be restored. To do this, when starting the installation of the Windows 10 operating system, click on the "System Restore" button and go to the "Diagnostics">>"Advanced Options">>"Command Prompt" menu, or simply press the key combination Shift + F10. A black Windows console window will appear:
We type commands in turn:
Bootrec /fixmbr bootrec /fixboot bootrec /RebuildBcd
Each of them must complete successfully. After that, restart the PC and try to run the installation again. Usually this is a disk controller error in bios menu The computer is solved and everything goes on without problems.
set-os.com
During the installation of the operating system, at the stage of formatting disks and creating partitions, the user may encounter the error “Windows cannot be installed to this disk. Your computer hardware may not support booting from this disc. Make sure the controller for this drive is enabled in the computer's BIOS menu."
Why does this error occur and how to fix it?
See also: Codes Windows errors 10 and ways to troubleshoot
Often, the error when it is impossible to create a partition for installing a new operating system occurs on older Windows 7 PCs. However, others Operating Systems, starting with XP and ending with Windows 10, are also not immune from such a problem.
This error can be caused by the following factors:
Method number 1. Via BIOS settings
To fix this error, you should boot into the BIOS and set the operating mode hard drive IDE. To do this, do the following:
If your PC has new firmware BIOS, then instead of IDE mode, you should enable EFI boot. To do this, do the following:
It is worth noting that with this change, it is possible that a new error will appear, which is associated with MBR or GTP partitions.
See also: How to install Windows 10 on a GPT and MBR disk?
If an additional cached SSD or other drive is installed on your PC or laptop, the problem may be due to it. To fix the problem, perform the following steps:
Method number 3. If the error is related to the GPT or MBR format
If during the installation of Windows 7, 8 or 10 you get the error “Windows cannot be installed to this disk. The selected disk has the GPT partition style, you should change the GPT format to MBR. To do this, perform the following steps.
After formatting the partition, it is worth restarting the PC and trying to install the OS again.
You can also follow the same steps for more in a simple way. In the BIOS, in the “Boot” section, in the “UEFI / Legacy Boot” item, and set Enabled, and in “ secure boot» - Disabled. After that, delete all partitions and create new ones. The format will be automatically changed.
SoftikBox.com
Comments on the entry: 4
Hi all! When installing Windows on a laptop, I got an error: Windows cannot be installed on this disk. Your computer's hardware may not support booting from this disc. Make sure that the controller of this drive is enabled in the BIOS menu of the computer.
I read on the Internet, someone says that you need to switch from achi to ide. Switched - did not help. I looked at the bios settings, well, in the laptop it’s so simple that there’s almost nothing to choose at all ... I reset Bios, it didn’t help ... Then I put the Windows disk back in and pressed system restore during installation (this is where the install button is). Selected command building. By the way, you can run it with Shift + F10.
We write bootrec / fixboot . Then we try to install. Helped me.
The fact is that Windows could not find the bootloader and did not understand what to do. This is how the error is solved installing windows on this disk is impossible.
AlexZsoft.com
At reinstalling Windows 7, an unexpected problem arose on the laptop - the BIOS and the Windows installer saw the hard drive, it was allowed to mark it, add / remove partitions, but things didn’t go any further, giving out a strange-looking message:
Windows cannot be installed to this drive. Your computer's hardware may not support booting from this disc. Make sure that the drive's controller is enabled in the computer's BIOS menu.
Why is it weird? In general, support for the AHCI (Advanced Host Controller Interface) mechanism has been announced since Windows Vista and the Windows 7 installation disk is licensed.
Well, God bless him, you can look for the guilty for a long time and hard, but it's easier to get into the BIOS and switch the AHCI Mode Control mode from c to . After that, it will become possible to disable Native AHCI Mode. Subsequently, you can return the settings back by installing the system and all drivers.
If you find the article useful, do not be lazy to like and share with your friends.
mdex-nn.ru
Windows cannot be installed on this drive (solution)
This manual details what to do if, when installing Windows, you are told that it is impossible to install Windows to a disk partition, and in detail - “Windows cannot be installed to this disk. Your computer hardware may not support booting from this disc. Make sure the controller for this drive is enabled in the computer's BIOS menu."
If you do select this section and click "Next" in the installer, you will see an error stating that we could not create a new one or find an existing one, with a suggestion to view additional information in the installer log files. The following will describe ways to fix such an error (which can occur in the Windows 10 - Windows 7 setup programs).
As more and more often on computers and laptops of users there is a variety in partition tables on disks (GPT and MBR), HDD operating modes (AHCI and IDE) and boot types (EFI and Legacy), errors are also becoming more frequent when installing Windows 10, 8 or Windows 7 caused by these settings. The described case is just one of such errors.
Fixing the error "Installation to this disk is not possible" using BIOS settings (UEFI)
Most often specified error occurs when installing Windows 7 on old computers with BIOS and Legacy boot, in cases where AHCI mode (or any RAID, SCSI modes) is enabled in the BIOS settings for SATA devices (i.e. hard disk).
The solution in this particular case is to go into the BIOS settings and change the hard drive mode to IDE. As a rule, this is done somewhere in the Integrated Peripherals - SATA Mode section of the BIOS settings (a few examples in the screenshot).
But even if you don't have an "old" computer or laptop, this option can also work. If you are installing Windows 10 or 8, then instead of enabling IDE mode, I recommend:
True, in this option you may encounter another type of error, in the text of which it will be reported that the selected disk contains an MBR partition table (correction instructions are mentioned at the beginning of this article).
Why this happens, I myself did not fully understand (after all, AHCI drivers are included in the images of Windows 7 and higher). Moreover, I was able to reproduce the error for installing Windows 10 (screenshots are just from there) - simply by changing the disk controller from IDE to SCSI for virtual machine Hyper-V "first generation" (i.e. with BIOS).
Whether the indicated error will appear during EFI boot and installation on a disk running in IDE mode, I could not check, but I admit this (in this case, we try to enable AHCI for SATA disks in UEFI).
Third party disk controller drivers AHCI, SCSI, RAID
In some cases, the problem is caused by the specificity of the user's equipment. The most common option is the presence of caching SSDs on a laptop, multi-disk configurations, RAID arrays and SCSI cards.
How to remove the window "make sure that the controller of this disk is included in the bios menu of the computer" during Windows installation
Sometimes it happens that during the installation of Windows, at the stage when you need to select the hard disk partition on which Windows will be installed, the error “Make sure that the controller of this disk is included in the bios menu of the computer” appears. Naturally, the installation does not go further.
Error text
In this article, you will learn what it means and how to fix the problem with the hard disk controller.
There are several options for the message "Make sure that the controller of this disk is included in the computer's bios menu".
One of the most likely is an incorrectly set hard disk mode in the BIOS. There are two main modes - Achi and IDE, which we wrote about in the article.
Sometimes on new motherboards, the UEFI / BIOS boot mode option contributes to the appearance of this error.
Less often, but there is also another situation. This is a corruption of the hard disk boot record and in this case it will need to be repaired.
There are as many options for fixing this problem as there are causes.
First you need the mode of operation of the hard disk. If it is IDE (Compatible)(Native Mode), then enable AHCI, and if it is AHCI, then switch to IDE (Compatible)(Native Mode).
Switching the Hard Disk Mode - Option 1
Switching the Hard Disk Mode - Option 6
Switching the Hard Disk Mode - Option 5
Switching the Hard Disk Mode - Option 4
Switching the Hard Disk Mode - Option 3
Switching the Hard Disk Mode - Option 2
If this does not help, then you should check the UEFI / BIOS boot mode option. If it is, then you should set it to "legacy" or "Legacy First".
Switch boot mode to Legacy
After all changes in the BIOS, do not forget to save them with the F10 button.
The last option is to try to check and repair the boot record of the hard drive.
To do this, press "shift" + "F10" when the error "Make sure that the controller of this disk is included in the bios menu of the computer" appears. This will launch the console.
Restoring boot record via console
I have already mentioned several times in my articles about SSD drive x, said that they are faster than usual and with their help you can upgrade your computer. And it would seem that installing them is a trivial thing, what could be easier, remove the old hard drive, install a new SSD , install Windows on it and rejoice, but in reality everything is not so simple. The fact is that in order to squeeze top speed from an SSD drive (otherwise why use it), you need to switch to AHCI (Advanced Host Controller Interface) mode in the BIOS. And this is where the surprises begin...
So, I have an old computer that decided to upgrade and install an SSD drive. Switched to AHCI mode in BIOS. To do this, I went into the BIOS (press the Del or F2 button (there may be other keys depending on the model of the motherboard), when you turn on the computer) in the "Main" menu, select "Sata Configuration".
And in "Configure Sata as" chose "AHCI"
Saved the settings, restarted the computer and started installing Windows. But that was not the case, an error occurred:
Started changing BIOS settings, even updated his version
, the result was one - this error constantly appeared. As a result, I decided to select IDE mode in BIOS and install Windows.
The installation was successful, then I decided to try switching back to AHCI mode in the BIOS, but this trick failed and Windows simply did not boot (in principle, I expected a similar result). Then I decided to do this - switch back to IDE mode, go to Windows and change the mode to ACHI in the registry editor.
Having returned the IDE mode, Windows has successfully booted, now you need to make changes to the registry. To do this, open the registry editor - press the key combination "Win" + "R" and type regedit.
In the registry editor, go to the path "HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Msahci", find the "Start" parameter, open it double click. Enter "0" in the "Value" field.
Everything, the system can be rebooted and set to AHCI mode in BIOS. As a result, everything worked, the SSD worked in ACHI mode. Windows booted up successfully and worked many times faster than with a regular hard drive.
So, if your old computer has ceased to please you with the speed of its work, installing an SSD drive, in my opinion, is the ideal solution. But do not forget about the minimum size random access memory- 2GB well, and the processor is desirable 2 cores at least 2 GHz each.
I hope this article helped you avoid the error:
Installing Windows on this drive is not possible. Your computer's hardware may not support booting from this disc. Make sure that the drive's controller is enabled in the computer's BIOS menu.
And it helped to upgrade your computer and increase its performance and speed.
» » Error "Windows cannot be installed to this drive"
Sometimes when installing Windows 7, 8 or 10, you may encounter a problem, which is that when you try to install the system on HDD, the system issues a warning: “Windows cannot be installed to this disk. Your computer's hardware may not support booting from this disc. Make sure that the drive's controller is enabled in the menu computer BIOS".
The problem, as a rule, is characteristic of old computers and laptops, but occasionally it also appears on new hardware. This usually happens when BIOS settings computer in the parameters of the hard drive mode is enabled AHCI or any other than IDE. So let's go to BIOS computer and set the mode of operation of our disk as IDE. This setting is usually located under integratedPeripherals or Advanced, and is usually called SATARAID/AHCImode, SATAmode, SATAAHCImode,ConfigureSATA or another name with a similar meaning.
I also met this way to deactivate the mode:
